NATURAL Latex

Natural Latex, as its name implies, is €œnatural€ which offers many benefits for use in sleep products. Consumers that have an organic lifestyle and have made numerous changes to remove most synthetic chemicals from their household tend to purchase 100% natural formulations. The elasticity, healthiness, and ability of Natural Latex to conform to your body, reducing pressure on your muscles and circulation is unsurpassed. The resulting benefits and luxurious comfort simply cant be matched by synthetic Latex. However, because it is a €œnatural€ product there are inconsistencies at the molecular level which cause Natural Latex products to wear at a faster rate than Synthetic Latex.

MAKING Latex - Latex FORMULAS

Both Talalay and Dunlop processes start with a formula mixture of liquid Latex. These formulas can be any of the following: 100% natural Latex rubber (harvested from rubber tree plants)100% synthetic Latex rubber (a man-made molecular copy of natural Latex rubber)Blended natural - synthetic Latex rubbers (specific blend ratios are proprietary) Note: there are small amounts of other materials required for processing liquid Latex into solid form which are necessary for all Latex production. (ingredients - amounts are proprietary) Latex International Talalay is produced using only 100% Natural or Blended formulations to meet optimum quality standards.

RUBBER TREE PLANTATION

In the wild, the tree can reach a height of up to 100 feet (30m). The white or yellow Latex occurs in Latex vessels in the bark, mostly outside the phloem. These vessels spiral up the tree in a right-handed helix which forms an angle of about 30 degrees with the horizontal, and can grow as high as 45ft. In plantations, the trees are generally smaller for two reasons: 1) Trees grow slower when they are tapped for Latex, and 2) trees are generally cut after 30 years because Latex production declines as trees age, and they are no longer economically viable.  The tree requires a tropical or subtropical climate with a minimum of about 1200mm/yr of rainfall, and without frost If frost does occur, the results can be disastrous for production. One frost can cause the rubber from an entire plantation to become brittle and break once it has been refined (needs reference).

Process

Each night a rubber tapper must remove a thin layer of bark along a downward half spiral on the tree trunk. If done carefully and with skill, this tapping panel will yield Latex for up to five years. Then the opposite side will be tapped, allowing this side to heal over. The spiral allows the Latex to run down to a collecting cup. The work is done at night or in the early morning before the day's temperature rises, so the Latex will drip longer before coagulating and sealing the cut. Depending on the final product, additional chemicals can be added to the Latex cup to preserve the Latex longer. Ammonia solution helps prevent natural coagulation and allows the Latex to remain in its liquid state. Plastic bags containing a coagulant have replaced cups in many plantations in Malaysia. This form of Latex is used as the raw material for Latex concentrate, which is used for dipped rubber products or for the manufacture of ribbed smoke sheet grades. Naturally coagulated Latex, sometimes referred to as cup lump, is collected for processing into block rubbers, which are referred to as technically specified rubbers (TSRs). The serum left after Latex coagulation is rich in quebrachitol, a cyclitol or cyclic polyol

HARVEST OF Latex

Harvesters make incisions across the Latex vessels, just deep enough to tap the vessels without harming the tree's growth, and the Latex is collected in small buckets. This process is known as rubber tapping. Latex production is highly variable from tree to tree and across clone types.

Latex Foam Prehistoric uses
The first use of rubber was by the Olmecs, who centuries later passed on the knowledge of natural Latex from the Hevea tree in 1600 BC to the ancient Mayans. They boiled the harvested Latex to make a ball for a Mesoamerican ballgame.

Rubber tapping is the process by which the Latex is collected from a rubber tree. An incision is made in the tree's bark, which cuts through the Latex vessels, from which the product then flows. Timing of the incision must be planned within the planting cycle to optimise the Latex yield. Rubber tapping is an environmentally attractive land use. Jungle rubber is essentially old secondary forest, strongly resembling the primary forest. Its species' richness is about half that of the primary forest. Michon and de Foresta (1994) found that sample jungle rubber sites contained 92 tree species, 97 lianas, and 28 epiphytes compared to 171, 89, and 63, respectively, in the primary forest, and compared to 1, 1, and 2 in monoculture estates. Thiollay (1995) estimated that jungle rubber supports about 137 bird species, against 241 in the primary forest itself. Jungle rubber is expected to resemble primary forest in its hydrological functions. Monoculture rubber tree plantations have far less of an environmental impact than other crops, such as coffee or especially oil palm. In Information Technology the term 'Rubber tapping' is sometimes used as a lampoon for planned Production deployments, where the timing of the deployment is crucial. Such deployments are generally done late in the night when customer activity is minimum.

GOTS Global Organic Textile Standard

• LATEXPEDIC PHOENIX NATURAL MATTRESS SLEEP SHOP